![]() When you instantiate NX, it automatically launches WavesHeadTracker, which opens in a separate window, and shows a feed from your your Webcam, with a 3D green box around your head, reminiscent of something from The Matrix. In the stereo version of NX, the GUI features a pair of speaker icons connected by a yellow line, and a top-view, 3D graphic of a human head. The NX plug-in interface is where you do most of the adjusting (except for head-tracking parameters). NX can be instantiated in mono-to-stereo, stereo, and 5.1 or 5.0 surround. The two you’re most likely to use in a DAW environment, though, are the stereo and 5.1 components. The frequency response that you get in NX is heavily impacted by your headphones, so the more accurate they are, the better. You put it on the master bus while you’re mixing, but then you bypass it before you bounce your mix. Unlike a speaker simulator like the Focusrite VRM Box, NX doesn’t try to emulate any particular types of monitors. Instead, it uses psychoacoustic technology to simulate a treated mixing room, free from acoustic anamolies the theory being that in such a pristine environment, you will be better equipped to make mixing decisions. If you’d prefer not using an external drive, but still need to switch computers occasionally, it’s quite easy to move your authorization between two machines using Waves Central. ![]() You can only authorize it on one device at at time, but it can be either your computer or an external drive (even a flash drive). You install NX just like any other Waves plug-in, using the free Waves Central installer application. Details, details The interface for the NX stereo component When I first got a demo of it at NAMM, I was sure it would cost at least $500, and was flabbergasted (in a good way) when I heard the actual price. Possibly the most mind-boggling aspect of this plug-in is that it costs just $99. Using the webcam on your computer or an optional head-tracking accessory sold by Waves (not available yet), it follows your head movements and adjusts the virtual acoustics to compensate. NX comes with the WavesHeadTracker application, which loads when you open the plug-in. i assume you need to have a MultiChannel Buss to place this plugin on. HTHhey thx very much !!! i will load up the demo in Logic. I've been meaning to ping Waves and ask, but have been too busy. The head tracker software keeps popping up however, and it seems that there's a way to turn it off, but I haven't had immediate success. The new binaural stage for NX seems really nice, and the other good thing is that it actually performs at 96Khz session rate, where most don't even work, or like the PA DearVR, run at 96Khz, but only offer the response of 44.1. That said, I do sometimes use the crosstalk feature in Goodhertz Can Opener and the EQ profiles in Tonebooster's Morphit (mostly to tame the midrange in a pair of Etymotics), but these have been off my mix buss for a while now. There are so many nice flat response headphones, I don't think more is necessary. Like some folks here, I don't see too much value in enhancement technologies for headphones. i think you can but would like some real world experience !!You can run the software by itself. Still would ove to know if you can run the Software Alone. It made the process less tiring for the ears. With too much low-end spacialisation also (at least that's My point of view).īut NX is good when you have to write and compose on headphones. And I ended with a mix with a lot of low-end content that ruins a bit the dynamic of My mix. I've tried (it was a test don't blame me) to mix with it from Start to finish. But I guess it could also be that it's not a good match for my headphones (Philips Fidelio X2)?Well it doesn't fit to My headphones too. ![]() I'm a bit disappointed that I bought this plugin, but at least I bought it when it was 50% off so it's not that bad. I'm using it without that webcam tracking thing. ![]() The result doesn't sound good in my headphones at least. It just doesn't sound like monitors in a room to me (I've measured my head and put in those values in the head modeling section), and so far my mixes doesn't turn out so well using NX (and no, I'm not blaming the plugin for that). I have the same experience with Waves NX.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |